ikan Uploader :
Directory : /usr/include/linux/can/
Upload File : |
| Current File : //usr/include/linux/can/netlink.h |
/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
/*
* linux/can/netlink.h
*
* Definitions for the CAN netlink interface
*
* Copyright (c) 2009 Wolfgang Grandegger <wg@grandegger.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the version 2 of the GNU General Public License
* as published by the Free Software Foundation
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#ifndef _CAN_NETLINK_H
#define _CAN_NETLINK_H
#include <linux/types.h>
/*
* CAN bit-timing parameters
*
* For further information, please read chapter "8 BIT TIMING
* REQUIREMENTS" of the "Bosch CAN Specification version 2.0"
* at http://www.semiconductors.bosch.de/pdf/can2spec.pdf.
*/
struct can_bittiming {
__u32 bitrate; /* Bit-rate in bits/second */
__u32 sample_point; /* Sample point in one-tenth of a percent */
__u32 tq; /* Time quanta (TQ) in nanoseconds */
__u32 prop_seg; /* Propagation segment in TQs */
__u32 phase_seg1; /* Phase buffer segment 1 in TQs */
__u32 phase_seg2; /* Phase buffer segment 2 in TQs */
__u32 sjw; /* Synchronisation jump width in TQs */
__u32 brp; /* Bit-rate prescaler */
};
/*
* CAN harware-dependent bit-timing constant
*
* Used for calculating and checking bit-timing parameters
*/
struct can_bittiming_const {
char name[16]; /* Name of the CAN controller hardware */
__u32 tseg1_min; /* Time segement 1 = prop_seg + phase_seg1 */
__u32 tseg1_max;
__u32 tseg2_min; /* Time segement 2 = phase_seg2 */
__u32 tseg2_max;
__u32 sjw_max; /* Synchronisation jump width */
__u32 brp_min; /* Bit-rate prescaler */
__u32 brp_max;
__u32 brp_inc;
};
/*
* CAN clock parameters
*/
struct can_clock {
__u32 freq; /* CAN system clock frequency in Hz */
};
/*
* CAN operational and error states
*/
enum can_state {
CAN_STATE_ERROR_ACTIVE = 0, /* RX/TX error count < 96 */
CAN_STATE_ERROR_WARNING, /* RX/TX error count < 128 */
CAN_STATE_ERROR_PASSIVE, /* RX/TX error count < 256 */
CAN_STATE_BUS_OFF, /* RX/TX error count >= 256 */
CAN_STATE_STOPPED, /* Device is stopped */
CAN_STATE_SLEEPING, /* Device is sleeping */
CAN_STATE_MAX
};
/*
* CAN bus error counters
*/
struct can_berr_counter {
__u16 txerr;
__u16 rxerr;
};
/*
* CAN controller mode
*/
struct can_ctrlmode {
__u32 mask;
__u32 flags;
};
#define CAN_CTRLMODE_LOOPBACK 0x01 /* Loopback mode */
#define CAN_CTRLMODE_LISTENONLY 0x02 /* Listen-only mode */
#define CAN_CTRLMODE_3_SAMPLES 0x04 /* Triple sampling mode */
#define CAN_CTRLMODE_ONE_SHOT 0x08 /* One-Shot mode */
#define CAN_CTRLMODE_BERR_REPORTING 0x10 /* Bus-error reporting */
#define CAN_CTRLMODE_FD 0x20 /* CAN FD mode */
#define CAN_CTRLMODE_PRESUME_ACK 0x40 /* Ignore missing CAN ACKs */
#define CAN_CTRLMODE_FD_NON_ISO 0x80 /* CAN FD in non-ISO mode */
/*
* CAN device statistics
*/
struct can_device_stats {
__u32 bus_error; /* Bus errors */
__u32 error_warning; /* Changes to error warning state */
__u32 error_passive; /* Changes to error passive state */
__u32 bus_off; /* Changes to bus off state */
__u32 arbitration_lost; /* Arbitration lost errors */
__u32 restarts; /* CAN controller re-starts */
};
/*
* CAN netlink interface
*/
enum {
IFLA_CAN_UNSPEC,
IFLA_CAN_BITTIMING,
IFLA_CAN_BITTIMING_CONST,
IFLA_CAN_CLOCK,
IFLA_CAN_STATE,
IFLA_CAN_CTRLMODE,
IFLA_CAN_RESTART_MS,
IFLA_CAN_RESTART,
IFLA_CAN_BERR_COUNTER,
IFLA_CAN_DATA_BITTIMING,
IFLA_CAN_DATA_BITTIMING_CONST,
IFLA_CAN_TERMINATION,
IFLA_CAN_TERMINATION_CONST,
IFLA_CAN_BITRATE_CONST,
IFLA_CAN_DATA_BITRATE_CONST,
IFLA_CAN_BITRATE_MAX,
__IFLA_CAN_MAX
};
#define IFLA_CAN_MAX (__IFLA_CAN_MAX - 1)
/* u16 termination range: 1..65535 Ohms */
#define CAN_TERMINATION_DISABLED 0
#endif /* !_UAPI_CAN_NETLINK_H */
........